Skip to content
GUOCUI BIO TECH Skincare OEM/ODM

Private Label 7% Glycolic Acid Cream 50 g – OEM/ODM Manufacturer

Direct answer: this reference is a 7% glycolic acid leave-on cream in a 50 g / 1.76 oz white jar with a silver waist band, presented in a printed folding carton.

Next step: send the fill weight, jar type, pH direction and destination market to the Guocui team, or open a private label quote for this cream with your artwork attached.

The packshot carries the descriptor 7% Glycolic Acid Cream, the line Anti-acne formula, a three-icon strip reading acne treatment, moisturizing and exfoliation, an ingredient callout Alpha hydroxy acid — Glycolic AHA, the phrase reduces lines & wrinkles, a mock wordmark and a your logo panel.

Every one of those lines is packaging copy, not a test result: the source folder holds packshots only, with no formula sheet, no pH reading, no stability report, no microbiological test and no certificate. This page therefore quotes no measured exfoliation rate, no pH value, no clinical outcome and no registration status. Guangzhou Guocui Biological Technology Co., Ltd. compounds, fills, labels and export-packs this jar format in Guangzhou, and each specification below is fixed per order rather than read off the image.

Private label 7% glycolic acid cream: a 50 g white jar with a silver waist band and printed carton, GUOCUI reference unit for OEM/ODM development
The reference unit: a 50 g white jar with a silver waist band and its outer carton, printed with a percentage descriptor, an anti-acne line, an AHA callout, three benefit icons and a logo panel — all pack copy, none of it a measurement.

Product positioning

A leave-on acid is a different commercial problem from a rinse-off acid. A toner, a peel or a wash carries the acid for a minute and is then diluted away; a cream keeps whatever you put in it in contact with skin for hours, in a package the buyer opens twice a day for the life of the unit. That single difference moves the whole brief: the percentage on the front of the carton becomes the least interesting number on the specification sheet, and the questions that actually decide whether the product ships are how much of that percentage stays in free-acid form at month eighteen, what the emulsion does to the jar gasket, and whether the words on the carton are legal in the country it lands in.

This jar is therefore best understood as a low-pH emulsion project with a marketing decision attached, not as a commodity moisturiser with an acid dropped into it. Buyers who treat it as the second thing tend to come back with a reformulation request after the first stability pull; buyers who treat it as the first thing usually end up with a two-SKU line, because once the pH and preservation architecture are settled, a second strength or a second texture is a small increment.

The three icons on the right of the packshot — acne treatment, moisturizing, exfoliation — describe three different regulatory categories in most markets, and only one of them is normally a cosmetic claim. That gap, not the formula, is where most launches stall. The rest of this page treats the formula, the pack and the wording as one decision, because in a leave-on acid they are.

Suitable buyers

Fit is about the shape of the brief, not about who is allowed to enquire. This format tends to suit:

  • Brands that already sell a rinse-off acid and want the leave-on counterpart, where the customer already understands AHAs and the new page has to explain format rather than category.
  • Pharmacy and dermo-cosmetic ranges building a blemish or texture step that has to sit between a cleanser and a moisturiser without adding a fourth product to the routine.
  • Brands whose claim list is already drafted and who need a manufacturer to tell them which lines survive the destination market before artwork goes to print.
  • Distributors importing into markets with an established AHA category, where shelf comparison is on texture and packaging rather than on education.
  • Buyers standardising several SKUs on one jar, where a single 50 g component carries a night cream, a spot cream and an exfoliating cream with different label panels.
  • Gifting and travel assortments that need a small, sealable jar with enough lid area for a printed story and a batch or QR code.

It is a poor first project for a buyer who cannot yet name the destination market, because the acid level, the pH, the preservation system and the claim wording all branch off that one answer. It is also a poor fit where the artwork depends on a drug-style indication, since the carton would then have to be built for a registration route rather than a cosmetic one.

SEO and buyer keywords

The searches that arrive at a page like this sit at three different points in the buying process, and they use three different vocabularies. Mixing them in one sentence is how a page ends up ranking for nothing.

  • Format and component intent: 7% glycolic acid cream, glycolic acid face cream 50 g jar, AHA cream private label jar, low pH face cream manufacturer, exfoliating cream in a jar.
  • Private label and sourcing intent: glycolic acid cream OEM manufacturer, private label AHA cream supplier, custom exfoliating cream contract manufacturing, glycolic cream wholesale Guangzhou.
  • Compliance and formulation intent: claim safe acne wording cosmetics, AHA cream pH requirement, glycolic acid cream stability in a jar, leave-on AHA preservation, glycolic acid cosmetic versus drug claim.

Those clusters map onto three different page types on this site: this article for the format decision, the 7% glycolic acid toner page for the rinse-off version of the same acid, and the private label catalog for format comparison across categories.

Custom formula directions

The brief below is written as a set of decisions rather than a recipe. None of it is a specification until a sample has been made and measured; it is the list of things that have to be settled before that sample is worth making.

The acid belongs to the water phase

Glycolic acid is water soluble, so in an emulsion it lives almost entirely in the aqueous phase and behaves according to what that phase is doing. Two consequences follow. First, the percentage describes the whole formula while the acid only acts from the water it sits in, so a rich, high-oil cream and a light gel-cream carrying the same percentage do not deliver the same experience. Second, anything that shifts water between phases after filling — evaporation from a jar, a phase inversion on the shelf, a pH drift from the container — changes the free-acid concentration without changing the label. That is why a leave-on acid brief should carry an aqueous-phase target, not only a whole-formula percentage.

The pH window, not the percentage, is the working specification

Glycolic acid has a pKa of roughly 3.8, which means the proportion present in the free-acid form — the form that does the exfoliating work — is set almost entirely by pH. Move a cream from pH 4.0 to pH 3.4 and the free-acid fraction rises sharply at the same stated percentage; buffer it to pH 4.8 and most of the acid is present as glycolate. Two practical rules follow for the brief. A low-pH emulsion needs an acid-tolerant thickener, because carbomer-type polymers depend on neutralisation to build viscosity and lose most of it in this window, which is why low-pH creams usually lean on electrolyte-tolerant gums or associative systems. And the pH has to be re-measured on the finished batch and again on stability, because a drift of a few tenths over shelf life moves the product more than a 1% change in the stated number ever would. This page does not publish a target pH for the reference unit: the packshot carries no measurement, and the right window depends on the destination market’s labelling rules and on how the brand wants the product to feel.

“Acne” is a market decision before it is a formula decision

The carton says anti-acne formula and the icon strip says acne treatment. Those words do not travel the same way everywhere. In the European Union and the United Kingdom, treating or preventing acne is a medicinal function, so a cosmetic cream may describe appearance and texture but may not claim to treat the condition. In the United States, acne is handled through an over-the-counter drug pathway with its own monograph, so a cream carrying that claim is not simply a cosmetic. Other markets sit between the two. The practical consequence for a private label project is that the claim list is agreed before artwork, not after: brands usually keep the cosmetic route and reword towards visible texture, oiliness and the look of blemished skin, or they commit to the registration route that the stronger wording requires. Neither choice is a manufacturing problem, but choosing late is.

Preservation in a unit that is opened twice a day

A jar is the hardest packaging format to preserve, because every opening admits air and fingers, and a 50 g unit in daily use is opened perhaps sixty times before it is finished. The low pH helps here rather than hurting: organic acid preservatives such as benzoic and sorbic acid are only active in their undissociated form, which is exactly what a pH below 5 provides. The complication is that they partition into the oil phase and lose effective concentration in the water where they are needed, and that the effective window is narrow. That is why the preservation strategy, the pH target and the challenge test are one decision in an acid cream, and why a formula that passes at the pilot scale can still fail after the emulsifier or the fragrance is changed.

Texture, fragrance and the colour of the cream

The reference cream reads as an opaque white in the packshot, which is a look, not a specification. A white, glossy cream usually implies an emulsion built for body and a fairly high oil phase; a gel-cream carrying the same acid will look translucent and feel lighter. Colour is a separate question: a low-pH water phase will shift many natural extracts and some pigments over shelf life, so a tint that matches the photo on day one is not evidence that it survives month twelve. Fragrance is a third: an acid cream can carry one, but the fragrance blend has to be checked for acid stability and for the allergen declaration that the destination market requires. Where a brand wants a fragrance-free story instead, that decision should be taken with the preservation route, since some preservation systems bring their own odour.

Packaging options

Jar, tube or airless

The 50 g jar in the photo is a straight-wall jar with a decorative waist band and a screw lid, which is a good default for a cream that has to show texture on a shelf or in a hand. Its weaknesses are known and fixable: the wide mouth invites contamination, so a shrink band, an inner seal or a spatula changes the buyer’s experience, and the headspace exposes the surface to air between uses. A tube reduces air contact and dispenses by pressure, which suits a thicker cream and a lower preservation burden. An airless pump removes air contact almost entirely and is the most protective of the three, at a higher component cost and with a fill-volume penalty. The decision usually comes down to whether the brand is selling texture on shelf or stability in use, and many ranges end up using a jar for the hero pack and a tube for the travel or refill size.

Label, carton and the dual fill statement

The packshot shows a wraparound label on the jar and a printed carton, with the fill stated in two units — 50 g and 1.76 oz. Keeping both units on the label is normal for export and costs nothing at artwork stage, but it has to be consistent between the jar and the carton, because a mismatch is a labelling defect in most destination markets. Practical constraints on a 50 g jar are the label height available between the shoulder and the base radius, the number of print colours the chosen route can hold, and whether the batch code, PAO symbol and full ingredient list fit the panel the artwork leaves free. The your logo callout in the image is the supplier’s own placeholder, not a licensed brand mark, and the wordmark printed on the reference unit is a mock.

Export packing and marketplace photography

A cream in a jar is heavy relative to its value, so carton configuration matters more than it does for a mask or a stick. Typical routes are a printed unit carton inside a shipper, or a bare jar with a shrink band and a shelf-ready tray. Secondary packaging also decides how the product photographs: a unit carton gives a marketplace listing one clean silhouette and a second face for the ingredient panel, while a bare jar photographs better open. Whichever route is chosen, the carton dimensions, the fill statement, the batch and expiry fields and the barcode area should be agreed in the same artwork round as the label, because a late change to any of them restarts the print run.

Sample and QC workflow

  1. Brief and claim list. The destination market, fill weight, jar or tube decision, target feel and the exact wording the brand wants on pack. The claim list is reviewed here, before any formula work, because it decides whether the project is cosmetic or registration-led.
  2. Formula direction and pilot batch. An aqueous-phase target, a pH window, a preservation route and an emulsifier system are proposed against the brief, then made at pilot scale. Reworking the brief after the pilot is normal; reworking it after the artwork is expensive.
  3. Measurement on the sample. pH on the finished emulsion, viscosity and texture against the reference, appearance and odour, and fill-weight check. Whatever the brand intends to print has to be supportable at this stage, and a stated percentage is confirmed here rather than assumed from the brief.
  4. Compatibility and stability. The product goes into the actual jar and the actual label, because the gasket, the inner lacquer and the adhesive all see the acid. Accelerated and real-time pulls track pH drift, phase separation, colour shift and weight loss, and the microbiological challenge is run on the preserved formula, not on a simplified lab version.
  5. Approval, then bulk. Golden sample sign-off covers colour, odour, texture, fill and pack. The batch record, the certificate of analysis and the safety data are issued against that approved specification, and any market-specific file is confirmed at this point rather than assumed.

MOQ and quotation

Minimum order quantity on a jar cream is not one number. Three separate minimums bind at the same time, and the highest one wins: the smallest batch the formula can be made in without losing its pH and viscosity control, the smallest quantity the jar and lid can be supplied in with the chosen decoration, and the smallest label and carton print run that the artwork can be produced at. A brand that changes only the lid colour can move one of those three minimums without touching the other two, which is why a quote is built from the brief rather than from a catalogue.

The three starting bands used across this site’s private label pages — 500, 1,000 and 3,000 units — describe which minimum is likely to bind, not a price list and not a commitment for this product. A 50 g jar with a printed carton and a modest label usually lands in the lower bands; a decorated jar, a two-piece carton and a short print run can push the same cream into a higher one. Quotation is issued on request, after the fill weight, the component route, the claim list and the destination market are known, because all four change the answer.

  • What is quoted: unit price at the agreed specification, tooling or plate costs where a component is customised, sampling cost, and the packaging cost separately from the fill cost so the buyer can see which minimum is driving the order.
  • What is not quoted: a certification, a test result or a registration that has not been carried out. Where a destination market needs a filing, that is a separate project with its own timeline.
  • What changes the number fastest: a last-minute jar change, a claim that forces a different regulatory route, or an artwork revision after the print plates are made.

Buyer FAQ

Is the 7% figure a tested result?

No. The percentage is packaging copy on the reference unit, and the source folder contains packshots only — no formula sheet, no assay, no stability data. In production the figure is a formula target that has to be confirmed by batch analysis, and if the brand intends to print it, the specification and the test method should be agreed before the first bulk order.

Can the cream legally say “acne treatment”?

Not as a cosmetic claim in the European Union or the United Kingdom, where treating acne is a medicinal function; in the United States the same words sit in an over-the-counter drug pathway rather than a cosmetic one. The cosmetic route keeps the product but changes the wording — visible texture, oiliness, the look of blemished skin — and the drug route keeps the wording but adds a registration project. The choice belongs in the brief, with the destination market named.

What pH should we specify?

There is no universal answer, and this page deliberately does not invent one. Glycolic acid’s pKa of roughly 3.8 means the free-acid fraction changes quickly across the 3.4–4.2 band, so the window is chosen against the intended strength, the destination market’s labelling rules and the brand’s tolerance target, then confirmed on the finished batch and again on stability. A specification that names only a percentage and no pH is not a specification.

Jar or tube for an acid cream?

A jar shows texture and carries the widest artwork, but it is opened constantly and exposes the surface to air; a tube reduces air contact and usually lowers the preservation burden; an airless pack is the most protective and the most expensive. Many ranges use the jar for the hero size and a tube for travel, which keeps one formula and two components rather than two formulas.

Does the acid attack the jar or the label?

It can affect both, which is why compatibility is tested on the real components rather than assumed. A low-pH emulsion can attack an unqualified inner lacquer or a metal collar, migrate into a pressure-sensitive adhesive, and stain a carton board at the fold. The gasket, the inner coating, the label stock and the adhesive are checked with the finished product in stability, not with water.

How is this different from your glycolic toner page?

The acid is the same; the contact time is not. The 7% glycolic acid toner is a rinse-off or wipe-off liquid step where the acid is diluted away within a minute, so bottle and closure dominate the brief. This cream stays on the skin, so pH control, low-pH preservation and pack compatibility dominate it instead. Brands often launch the toner first and add the cream once the customer understands the acid.

Start a 7% glycolic cream brief

A useful first message names four things: the destination market, the fill weight and pack type, the feel the brand wants, and the exact wording it hopes to print. With those four, the project team can propose an aqueous-phase target, a pH window and a component route, and tell you which of the three minimums is likely to bind before any sampling cost is incurred. Send the brief through the contact page, or use the quote form if the artwork is already drafted. The wider range of jar and tube formats sits on the products page.

Where to read next

Get OEM/ODM insights and claim-safe wording guides.

No spam. Unsubscribe anytime. One email every 3-4 days max.